vertical cutting dryer

One
year would seem very short if you also have something to do and put in place
your days full. It is very just like yesterday when GN attended CIPPE 2015 via
Beijing, it comes the new yr and the new CIPPE Acrylic Show, CIPPE 2016.

Exactly what did GN show intended for CIPPE 2015?
1 . At the start of Year 2015, GN developed a compact drilling cuttings waste
materials management system, a combination of GNCD930C vertical cuttings dryer
along with GNLW363CG-VFD
decanter centrifuge
, between your two equipment is a tank for receiving the
drilling water from the vertical cuttings dryer and for feeding the centrifuge.
It is a compact design, also suitable for land transportation without having
taking down the centrifuge along with V-G dryer.

2 . GN whole family of decanter centrifuges. For the most popular model
GNLW363CG-VFD you could check on the
waste management system
skid, different centrifuges, GNLW223 of in search
of inch bowl, GNLW452 regarding 18 inch bowl however middle speed, GNLW553 of
twenty-two inch bowl.
3. Principal equipment for solids control systems, like shale shaker, mud cleaner and and
so forth

During CIPPE 2015, many purchasers and potential clients visited GN Solids
Control’s booth along with checked GN’s products, a few of them visited GN’s
factory having seen GN’s booth and they gifted good comments on GN’s producing
capability.What GN will show in CIPPE 2016?

Looking back to the past yr, GN has accomplished various achievements:
1 . all principal equipments was improved and also updated models are within
design, coming soon for CIPPE 2016.
2 . new machines and systems are well analyzed to be useful on jobsites, will
be introduced to clients inside near future.
3. GN’s completely new factory will be put into use in addition to new
workshops are below construction.

What to know more specifics? Come to us at address listed below:
Address: New China Intercontinental Exhibition Center, Beijing; Number 88,
Yuxiang Road, Tianzhu, Shunyi District, Beijing
Occasion Time: March 29-31, 2016
GN Booth No .: LOUNGE E2 -E2200, booth place 272m2.
Booth Location: http://public.cippe.com.cn/static/hall/2016bj/hall_e2.jpg
Appointment Email: sales@gnsolidscontrol. com
GN Factory Location: 40KM to the Exhibition Center (40 Minutes Drive)

image

GN Solids Control
provided one set of mud system for The european union GN
Solids Command manufactures various mud these recycling systems and most of
these mud systems are widely used within over 60 countries. As increasing
numbers of countries pay attention to the environment safety, GN mud
recycling system
 are getting more and more popular.

Lately, GN Solids Control only provided one set of mud system that using in h2o
well drilling for The european union. GN Solids Control mud systems
successfully won this kind of project due to the large productive projects that
we did ahead of. And GN Solids control also has many certifications that prove
GN has been attempting to be the No . 1 solids control manufacturer in the
world. Vouchers such as API, DNV, ISO are available since the establishment.

This kind of GN water well mud system is purchased by on the list of leading
well drilling firms in Europe. They will recycling the drilling mud and
recycling the water. This system is like the bellowing equipments:

image

1 .GN
Double Deck Shaker

Which has a compact structure, GN dual deck shaker is mainly useful for two
phase separation. The top shaker is equipped with shaker displays have larger
opening, whilst the bottom shaker is equipped with displays have small opening.
Going fluids will be separated with the upper deck shaker beforehand, then it
can be further split up by the bottom shaker.

2 . GN Decanter
Centrifuge

GN centrifuge GNLW363 is traditionally used to separate out pretty good solids
from 2 microns to 5 microns. The spinning bowl diameter is 14inch, with a high
rotating increase to 3200 rpm, often the G force can get to to 2062G.

3. GN Screw Pump

GN good displacement pumps, also referred to as screw pumps, they are mainly
utilized to feed into decanter centrifuge without agitating the drilling mud
too much.

4. GN mudTank

Shaker, centrifuge along with screw pump are attached with one mud tank. On
this company design, GN drinking water well mud system can be utilized in many
different worksites.

Related Posts

Among all the Chinese Solids Control
suppliers, even commented by its peers in this industry, GN Solids Control has
a good reputation, because since its establishment several years ago, GN has
been determined to provide the oil and gas industry the best quality equipments
and most efficient solutions and to stand an good example for Made in China.

Now, GN Solids Control became the second
to none solids control company and the main reasons are as below:

1. GN always catches up with the newest
technology and GN R&D team always innoviate new designs per end users’
suggestions and apply the designs onto equipment quickly.

2. GN uses the top and reliable material
and parts, like the steel, GN uses the national standard steels from big steel
companies. The bearings and oil sealing, GN use SKF,
NSK, FAG and SOG. Only good material can ensure the good products.

3. GN is serious about after-sale service, like
the free of charge first time commissioning for main equipments, and for after
sale services, like spare parts, GN always has spare parts available in stock
and can do on line diagnose in case of troubles.

When talking about the real performance of
the equipment, the evidences from the clients who use them are more convincible
than those from the manufacturer. There are feedbacks from some of GN clients:

1. Baker Hughes, one of the largest Oil
Service companies in the world, choose GN as its solids control supplier in
China, and ordered 4 sets of complete GN drilling
cuttings waste management systems
to use in their Russian sites. And they
are giving good feedbacks and comments. You can see their jobsite working video
here:

2. An Nigerian drilling company, they
visited all China main solids control suppliers before ordering, and finally
chose GN for long term cooperation and use GN’s centrifuges, vertical
cuttings dryers
and pumps and etc. They are foreign companies in Nigeria,
they have to strictly obey all the regulations for protecting the environment,
and GN’s equipment and solutions helped them a lot.

3. other clients, like Scomi Oiltools, also
an international company for oil service, and some European companies, and etc.
Same equipments system is also working on Shell’s jobsite, see jobsite video
here.

Related Posts