solids control

As a professional waste management equipment supplier, GN is now ivesting a TDU, hopefully it will be tested soon.

Material will be fed to a feed hopper mounted on a pugmill. From the pugmill, material is transferred to the feed auger via a transfer auger. The feed auger conveys material into the PTU and maintains a seal/airlock for the system. From outside, that is how the TDU works.

Thermal desorption first regarded as an environmental remedy era in 1985 whilst it turned into particular inside the report of selection (ROD) for the McKin website in Maine. it’s miles regularly known as “low temp” thermal desorption to differentiate it from excessive temperature incineration. An early direct fired thermal desorption mission turned into the remedy of 8000 heaps of toxaphene (a chlorinated pesticide) infected sandy soil at the S&S Flying offerings web page in Marianna Florida in 1990,[1] with later initiatives exceeding one hundred seventy,000 tons on the Cape worry coal tar website online in 1999. a standing report from the united states Environmental safety company (USEPA) shows that thermal desorption has been used at sixty nine Superfund sites through FY2000. further, hundreds of remediation initiatives were completed the usage of thermal desorption at non-Superfund sites.

severa desorber sorts are to be had these days. a number of the greater not unusual kinds are listed below.

indirect Fired Rotary

Direct Fired Rotary

Heated Screw (hot Oil, Molten Salt, electric powered)

InfraredMicrowave

maximum indirect fired rotary systems use an inclined rotating steel cylinder to warmth the feed fabric. the warmth transfer mechanism is commonly conduction via the cylinder wall. on this form of machine neither the flame nor the products of combustion can contact the feed solids or the offgas. think about it as a rotating pipe inner a furnace with both ends sticking outside of the furnace. The cylinder for complete scale portable systems is typically five to eight ft in diameter with heated lengths starting from twenty to fifty ft. With a carbon steel shell, the most solids temperature is round 1,000 °F, whilst temperatures of one,800 °F with unique alloy cylinders are attainable. overall residence time on this type of desorber commonly stages from 30 to a hundred and twenty minutes. treatment capacities can range from 2 to 30 tons in line with hour for transportable gadgets.

It was not a good story, at this age, in the colleage time, when we heard of made in China, it is a shame, it is a joke. So when we go out to the real world, wanna find something we can be proud of, or change something to be. That is how I come here and stay so long time.

GN Team

GN Solids Control organized overseas tour for our excellent employee from engineering and production departments.There are two group, one group to Thailand, the other group to Europe. GN Select the excellent employees based on contribution, value recognition and loyalty to the company.

Then when we discuss with others, we know that thank god we are thinking in a simple way about the world, that high quality matters, no matter what background, what big untouchable clients, quality matters, cost matters. That is how basically the world works. So back to where we start, that is always we value.

As someone would say, employer is the client of employee. GN beleive the excellent employees are the core assets to the company. We take care of our employees, respect them, and offer them good salary and bonus. We know it’s our exccellent employees who delivered the value to customers. Every year, GN will select the best employees and offer them both material and spirit reward.

That is how we call it one team, one dream.

GN solids control Design and manufacture of container of combustible gas oilfield operations in the electronic déflagration system is the refinery along with gas gathering and switching exhaust and vent typically the gas processing plant, having fields of electronic combustion system can vent inflammable harmful gas ignited lose in order to eliminate its difficulties for environment and safety, is often a safe, environmental protection products. Besides used in refinery and also gas stations, oil field electric ignition device with mud gas separator, is now traditionally used in oil drilling executive.
Oil field the superiority regarding electronic ignition system
Digital ignition oil fields “artificial lighting” to “automatic operation”, reflect the humanistic thoughts and environmental demands. Making it necessary to use electronic combustion device, drilling, testing, development process, the release is often the truth. Over the past few decades, Flare feu are manual operation, persons close to flare points, can burn, burns easily, high risk; As well, the artificial operation timeframe is longer, the accuracy and reliability is not high, easy to produce toxic gas emissions for the atmosphere in great volumes, cause different degree of atmosphere pollution.
GN SOLIDS CONTROL Production of electronic feu device let the “shortcomings” stopped to exist. It can be currently of relief, timely, exact location setting off export spewed toxic flammable gas movement line, eliminating the damage connected with gas pollution to the atmosphere and human and pet.

GN power flare ignitor
Electronic ignition device besides used in refinery and filling stations, the device with mud propane separator, is now widely used inside petroleum drilling engineering, is actually a mature product, in home and sichuan oil and gas discipline in xinjiang, in spots like Iran, Egypt, venezuela abroad are using the product.
Electric ignition device is mainly made from DN200 (or 6) gasoline burner (torch), GDH : type 2 electronic igniter, firing equipment (gas tank, hose, etc . ), mud gas separator (matching) whenever used in drilling engineering, and so on This product adopts high performance electronic digital ignition circuit, its principal parts adopt imported ingredients and other parts and cables and wires with domestic high quality goods, stable performance, reliable perform.
Procedures:
Install the butano gas pipeline to safe practices of burner (torch) atmosphere inlet.
Pick up and start the actual electronic igniter current transformation and voltage amplification routine.
Open the gas tank, operating electronic igniter light source flash tube ignition (level), or directly open the particular emptying the firing on the gas valve, lit fireplace with electronic igniter pipe ignition (level 1).
Wide open the gas vent gateway cut, lit by the using up fire tube will mélodie (secondary ignition).
Close the actual gas tank, put out open fire tube, let the combustible in-take gas combustion.

GN Solids Control sell a series of solids control equipment and drilling waste management equipment including vertical cuttings dryer , shale shaker  , shear pump , oilfield shale shaker , mud cleaner , desander and desilter , vacuum degasser , Mud Gas Separator , decanter centrifuge , mud tank , mud agitator , etc . GN Solids Americal normally keep stock for GN main product and shale shaker , mud cleaner and decanter centrifuge always keep stock there to service local client .

 

Mud agitator is widely used in mud cleaning systems. It is utilized in the mud tank as well as on the vessel to avoid the actual particles from settling straight down. Mud agitator is composed of some sort of motor, a gearbox, the particular shaft and impellers. This can be a very small equipment for drilling field.
Normally, a drilling rig mud tank system should be equipment with a significant no . of agitators. The higher quality , of the tank sides, a lot more quality of the mud agitators.
Many clients do not how to choose the best mud agitators modes and know the different mud agitators from different brand and various design. The main difference is that, typically the gearbox type is different. You will find mainly 2 type of items motor for mud agitators: helical bevel type items motor and Worm and kit type.
The helical bevel type gear motoriswith 2-stage or 3-stage transmission period.
It is with foot-mounted, flange-mounted Mounting mode, short flange-mounted model, torque arm-mounted type.

Mud Agitator
Furthermore, the Output shaft ofthe helical bevel type accessory motoris solid shaft, ineffective shaft (with key, having shrink disc and with involute spline).
Features of Helical-Bevel Products box and motor regarding mud agitator
It is Large modular design of the helical bevel type gear electric motor.
The helical bevel variety gear motoris with High reloading support. It is with a secure transmitting and a low noise degree.
The helical bevel variety gear motor is with good performance sealing. It can be used for an array of industry application.
The helical bevel type gear generator is with a High efficiency. It will save power during operating.
The helical bevel style gear motoris low repair and it can reduce the cost of users.
Worm and gearmotor device agitators is one of the most popular kind mud agitator. The gear package is worm and gear kind for easy operation repairs and maintanance. The worm and gear package is utilize the gear in order to transmit the motor acceleration to the request RPM. It might be widely used.
GN Solids Control sell a series of solids control equipment and drilling waste management equipment including vertical cuttings dryer , shale shaker  , shear pump , oilfield shale shaker , mud cleaner , desander and desilter , vacuum degasser , Mud Gas Separator , decanter centrifuge , mud tank , mud agitator , etc . GN Solids Americal normally keep stock for GN main product and shale shaker , mud cleaner and decanter centrifuge always keep stock there to service local client .

GN keeps research and develop the best technology to manufacture top quality shaker screens for our clients,

Welcome come to know more info from our sales team.

Drilling mud service contractors around the world are all use the rectangular drilling fluid circulating tank because the installation and migration performance of the system works very well. Meanwhile, no matter how good the mud agitator perform in ideal situation, the drilling fluid tank all have corners that mud agitator’s propellers cannot reach and stir. In order to resolve this issue, install the mud gun in the top of the tank to agitate the far corner of the mud tank.

Mud Gun

GN Solids America LLC’s GNNJQ series Mud gun serve as supportive machinery to the mud agitator.  It comes with nozzle that either made fixed angle or 360 degree ration angles the positive spray-effect distance of mug gun is approx. 3 meters long.   The gun size is related with drilling fluid density, viscosity and nozzle spray speed.  Mud gun is installed the top of mud tank can be need adjusted as need at any time. A mud gun is connected to a motor-pump to stir the drilling mud and prevent the solids from sinking on the bottom of the mud tank. The mud is mixed by being suck- withdraw into a pipe by a powerful pump and inject  back into the mud tank by being pressured push through the nozzle of the mud gun. The process is similar to how jets spray in the dish washer.

 

Drilling mud is a wet mud like substance resembles like thick clay and is used to keep the drill head in controlled-temperature and carry the remnants of drilling cutting to the surface in water and oil or gas drilling operations. The mud is recycled and reused by passing it through several steps of filter and cleaning by screens of the shale shaker or mud cleaner and decanter centrifuge as it is circulated into the mud tanks then back to the drill well on the drilling rig. In order to keep the mud as liquid-liked as possible, a mud gun and mud agitator is used to keep the tank agitated and mixed.  Drilling mud is made by mixing water or oil with a clay-like substance and also other chemicals.